Repair Chipped Concrete Steps

Featured Product: Fast Setting Cement Patcher


PREPARATION

  • Prepare the surface by wetting the area to be repaired. This will prevent the concrete from absorbing the water from the Fast Setting Cement Patcher.


APPLICATION

  • Enhanced bonding can be achieved by mixing the material to a wet consistency (slurry coat).
  • Place some of the material, by hand, on the damaged area.**
  • Add additional product to the mix to create a thick consistency before making the repair.

** BE SURE TO WEAR GLOVES **


FINISHING

  • Place the material on the damaged area using a margin trowel.
  • As it begins to stiffen, shape the material to form the corner.
  • Complete the repair by using a brush to smooth any existing seams and blend the repaired area into the existing concrete.


Tip: When using Fast Setting Cement Patcher at 1/4 inch, Sakrete Bonder & Fortifier must be used.


For complete product information, please refer to the product data sheet.

Concrete & Sand Mix

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Post Setting - Round Post

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Post Setting - Square Post

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Filling a Round Hole (For Post Supports) and Filling Sakrete Form Tubes

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Polymeric Sand/Paver Set/Perma Sand

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


US Cold Patch

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


All Weather Black Top Patch

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Maximizer

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Maximizer Post Setting - Round Post

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Maximizer Post Setting - Square Post

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Maximizer Filling a Round Hole and Filling Sakrete Form Tubes

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Mortar Mix

Calculated results will reflect how many bags are needed for Block and Brick.

Enter the number of bricks (8" x 2" x 4") or blocks (8" x 8" x16") in the box below that you plan to use for your project. The calculator will then tell you the number of bags you need based on the different size of bags we carry.

This calculator is based on a 3/8" mortar joint. All yields are approximate and do not include an allowance for waste, uneven subgrade or any other variations from the joint size and brick and block sizes noted above.

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Surface Bonding Cement

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Sand

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


Top'n Bond & Flo-Coat

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


B-1 Leveler

All values are required and must be written numerically with decimals.
(Ex. 2, 2.25, or .5)


 

Amount Required


Results will change if form of measurement is updated.



Where to buy      Concrete Calculators      Product Videos     

Alternative Products

View Details
Topping, Bedding, Crack Repair
Sand Mix
View Details
Concrete Repairs - 1/2" to Feather-edge
Top'n Bond Concrete Patcher



Complementary Products

View Details
Low Odor Cleaner
Concrete & Asphalt Cleaner
View Details
Admixture & Brush-on
Concrete Bonder & Fortifier
View Details
Use as Curing Compound or Sealer
Cure 'n Seal